equipped with specially designed heat recessive stone soles and heat circulation system. T his system supplies an absolute uniform distribution of heating gases over all decks of the oven therefore excellent baking results. I t provides low energy consumption, it can be moved by
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:16:42 ]
Total power 15 KW P ower source AC380V Three-phase five-wire Total size 15000x13000x4000mm Maximum current 32A Width of belt 780 mm Belt speed 6 - 10meter / minute Heating way Gas heating H eating element Gas wall boiler plumbing Heating temperature 25 ℃ --45 ℃ H umidity cont
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:15:50 ]
1. Refrigeration System equipped with a set of refrigeration system in P re- C ooling and Q uick- F rozen zone respectively. 2. Refrigeration Units adopts popular brands BITZER Compressor, it consist s of Zell’s mid-temperature, spiral compressor in P re- C ooling zone and Zell
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:14:48 ]
1. the usage of the tunnel oven Suitable for loaf bread,buns, baguette, croissant,cakes,pita bread, arabic bread,bagel, tortilla, mamoul,panko etc. 2. The advantage of proportion of zero-pressure gas-fired tunnel oven 1) Insulation System A Using rockwool insulation hybrid cotton
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:12:57 ]
Introduction This machine is equipped with layer by layer transmission technology which is similar to European technology. The gear motor drives the gear on every layer through a spindles , and the gear stir the convey belt for movement. Every gear has intelligent power transmitt
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:10:20 ]
1. Long Dough Moulder OBLIK 2-2 Machine capacity up to 3600 pcs/h Dough weight range 50-2000 g Length of forming plate 2x650 mm Three pair of rollers with scrapers Remov a ble and foldable forming plate with two triangles Food approved plastic Teflon co ated exit collector Freque
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:07:38 ]
AOCNO full automatic hamburger and hot dog production line, which is the most advanced and modern line is equipped with these following multi single equipments A utomatic tilting dough mixer – automatic dough pump – automatic dough divider and rounder – automatic dough wafe
Hebei AOCNO Baking Machinery Co., Ltd [2015-04-23 14:04:55 ]
Overview Processing Method BTA internal chip removing Hole Diameter(mm) Φ 16 ~ Φ 30 Hole Depth(mm) 2000 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece rotating with constant speed Guide Sleeve pneumatically dri
陕西金石机械制造有限公司 [2015-04-23 09:35:47 ]
Processing Method BTA internal chip removing Hole Diameter(mm) Φ 16 ~ Φ 60 Hole Depth(mm) 1000 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece rotating with constant speed Guide Sleeve pneumatically drive Workpi
陕西金石机械制造有限公司 [2015-04-23 09:34:43 ]
Overview Processing Method double tube jet drilling Hole Diameter(mm) Φ 18.5 ~ Φ 40 Hole Depth(mm) 1000 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe feeding , fixed and non-rotation Workpiece frequency controlled rotating Guide Sleeve pneumatically drive Workpiece Clamping
陕西金石机械制造有限公司 [2015-04-23 09:32:49 ]
Overview Processing Method BTA internal chip removing Hole Diameter(mm) Φ 16 ~ Φ 30 Hole Depth(mm) 2500 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece rotating with constant speed Guide Sleeve pneumatically dri
陕西金石机械制造有限公司 [2015-04-23 09:31:25 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 3~ Φ 30 NC System GSK980TDC / FANUC OI Mate TC /SYNTEC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece mounted on the bench Guide Sleeve pneumatically drive and traverse
陕西金石机械制造有限公司 [2015-04-23 09:28:57 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 5 ~ Φ 30 Hole Depth(mm) 10 00 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece mounted on the bench Guide Sleeve pneumatically drive
陕西金石机械制造有限公司 [2015-04-23 09:27:46 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 3 ~ Φ 25 Hole Depth(mm) 10 00 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece mounted on the bench Guide Sleeve pneumatically drive
陕西金石机械制造有限公司 [2015-04-23 09:26:41 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 1.5 ~ Φ 8 Hole Depth(mm) 5 00 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece mounted on the bench Guide Sleeve pneumatically drive
陕西金石机械制造有限公司 [2015-04-23 09:25:35 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 5~ Φ 15 Hole Depth(mm) 10 00 Axis Centre Distance(mm) 207 (can be customized) NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece NC in
陕西金石机械制造有限公司 [2015-04-23 09:24:02 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 5~ Φ 30 Hole Depth(mm) 1 500 Bench Traverse Distance(mm) 200 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece fixed, non-rotation Gu
陕西金石机械制造有限公司 [2015-04-23 09:23:01 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 5~ Φ 20 Hole Depth(mm) 1 000 Bench Traverse Distance(mm) 200 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe high speed mechanical spindle; frequency control; simultaneously rotating and feeding W
陕西金石机械制造有限公司 [2015-04-23 09:21:11 ]
Overview Processing Method outside chip removing; gun drill Hole Diameter(mm) Φ 5~ Φ 30 Hole Depth(mm) 1 500 Bench Traverse Distance(mm) 200 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece double truck clamping,
陕西金石机械制造有限公司 [2015-04-23 09:16:41 ]
Overview Processing Method outside chip removing ; gun drill Hole Diameter (mm) Φ 10 ~ Φ 25 Hole Depth (mm) 500 NC System GSK980TDC / FANUC OI Mate TC Drill Pipe frequency control; simultaneously rotating and feeding Workpiece fixed, non-rotation Guide Sleeve axial restraint
陕西金石机械制造有限公司 [2015-04-23 09:07:04 ]
