sheet metal prices steel rods metal rods steel sheets
Product Quick Detail
- Place Of Origin
- China
- Minimum Order
- 1
- Packaging
- CTN
- Delivery
- 15 Days
Specifications
custom name plates, name plate manufacturers, custom
nameplates , custom metal
tags,
Name Plate Manufacturers,Custom Name plates,Metal Tags,Metal Labels,Signs, Decals in China.
China Name Plate Manufacturers,we custom name plates,metalphotos,tags,labels,signs,decals with logo
and printing. Material:Metal,Aluminum,Anodized Aluminum,Brass,Stainless Steel,Polycarbonate,Polyester,Vinyl.
Website: www.nameplatesmanufacturers.com
nameplatesmanufacturers.com
FAQ nameplate production process
Question: What should be using a diamond cutting tool in the production process nameplate pay attention to?
A: 1 tool clamping to be positive, smooth rotation of the workpiece clamping also positive, flat, tight, so as not to damage the tool.
2. Depth of cut to be small, about 0.1mm, to prevent damage due to eating too cutter knife.
3. To turn backward knife, after retracting stop.
Question: How to get twill cutting surface and grid?
A: To select the size and position of the workpiece positioned to get a good cutter ideal twill, thickness and knife sharp lines concerned. To get the lattice of the workpiece
before and after going on the cutter each cutting once.
Question: When pressing Braille signs, inconsistent thickness, how high light cutting?
A: It should be added on a carbide cutter roughing tool cutting leveling at first, then the diamond cutting tool, which also protects the highlight tool is not damaged, hardness
alloy tool also plays a balancing role when rotating cutter.
Question: How high light plate production fixed in the machine?
A: In order to combine solid, should be used in high-quality 500 # Nitto double-sided tape. Braille signage or squeeze out the back two legs fixed after perforation.
Question: Are high-gloss surface may Braille signage screen printing?
Answer: Yes. Such signs seen abroad, there is dry again in Braille printed transparent red ink, but also very beautiful.
Question: What highlights cutting new uses?
A: The use of different cutting tools and machine can process a bright line on the plate panel, the bright side and the bright hole. Vertical machine is also useful to make
special tooling on the machine table, carving a variety of patterns and designs on the workpiece.
Epoxy signs manual
Epoxy signs of manual operation:
???????Epoxy plate manual operation is different from Epoxy plate machining (For more see "Epoxy signage Operating Procedures"), to distinguish between specific request from for
comparison.
1, the first ready for all kinds of substrates, such as: nameplates, badges, medals, etc. into the oven preheating temperature requirement of 60 degrees, the purpose of the
removal of surface moisture.
2, the substrate was placed flat dehumidified consistent level of console board waiting drip.
3. The amount, take a clean beaker, accurate measurement, the B component, a 2: 1 weight ratio of mixing evenly (must be mixed, otherwise there will be sticky and with the
substrate surface delamination phenomena , the manufacturers of the products are the same to do this). (Note: the proportion of the manufacturers are not the same, as the case may be).
4, and then with a good mixture into a vacuum oven, open real pump, removing bubbles mix in a vacuum.
5, take in the clean needle, the needle after defoaming Shuijingjiao suction tube, then measure and drip evenly in the prepared substrate (ie: signs, trademarks, etc.) of the
surface, the general crystal layer thickness 2mm, let the natural leveling can be (Note: The above process is controlled within 30 minutes, so as not to increase the liquid viscosity, resulting
in inoperable).
6, the substrate 3-5 minutes after instillation Shuijingjiao observe glue surface without bubbles or dust particles, if any small bubbles, usable pin to pierce, found dead have
not stream Shuijingjiao to place, with Extradition can pin.of workers.
- Country: China (Mainland)
- Business Type: Manufacturer
- Market:Americas
- Founded Year:1994
- Address:
- Contact:Senka Huang
Other products from T&H Nameplate Co.
Relate products of sheet metal prices steel rods metal rods steel sheets
Custom stainless steel sheet fabrication,metal case fabrication
Custom stainless steel sheet fabrication,metal case fabrication,custom metal case-Dalian Yikerui Machinery Manufacturing Co., Ltdwas founded in 2021，a professional manufacturer of precision sheet metal and parts，covers an area of 10000m²，has more than 60 skilled ...
ODM/OEM professional stainless steel 316/303/304 sheet metal stamping parts
ODM/OEM professional stainless steel 316/303/304 sheet metal stamping parts with cnc laser cuttingbending-Dalian Yikerui Machinery Manufacturing Co., LTD., founded in 2021, is a professional manufacturer of precision sheet metal and parts. It covers an area of 10,000 square ...
