Walk-In System Installation Instructions
TOOLS NEEDED
Pen or Pencil to Mark Holes
Drill
Crescent Wrench
Step Stool or Ladder
Utility Knife to Cut Strips
IMPORTANT
Prior to installation, unroll all door strips and place them on a clean, flat surface in a warm atmosphere for a minimum of twenty-four (24) hours. This will allow the strips to return to their
original form.
1. Mount pre-drilled Walk-In Mount to wall above door. Use fasteners supplied by others for mounting (Diagram 1).
2. Next, slide all the 3/8 carriage bolts down the slot on aluminum mounting hardware (Diagram 2).
3. Starting at the left, place the first clear inside strip (A on the first two bolts keeping in mind the concave pattern in Diagram 4 below. Place the second inside strip (B) on the third and
fourth bolts and continue down the entire length accordingly (Diagram).
4. Again starting at the left and using the concave patte place the first outside strip ? on the second and third bolts. The next outside strip will fit on the fourth an bolts. Continue this down
the entire length accordingly (Diagram 3).
5. Place all washers and bolts onto screw and tighten finger tight.
6. The first strip on left is to be flush with edge of the aluminum hardware. Start this point with the nut, tighten securely tool. Next, take second nut in hand and the right to secure the strip
flat against aluminum hardware. Tighten second to tool. Continue this pattern until all strips flat and smooth and all bolts are secured.
7. The strips should be initially trimmed to give a minimum of ? clearance using utility knife. The door strips need to hang for 24 to 28 hours before the final trim to allow for proper
alignment.
The Nill Building Solutions Outside Angle Flange can be used to mount attachments around the edge of your project. Various sizes available for your application. This product is ideal for installation of GLASS RAILINGS and much more. Product Features: PATENT No. 11,591,799 90 ...
Come From Nill Building Solutions
Nill Building Solutions has revolutionized the Glass Railing Fascia Mount Standoff by incorporating our Lag fastener into this piece. Our waterproof lag flange enables this piece to attach on top of the envelope and provide 100% waterproof protection. Product Features: PATENT ...
Come From Nill Building Solutions
8t Ft.Vienna Stainless Steel Sliding Barn Door Hardware. Designed for 3/8\" and 1/2\" glass, suitable for: *room dividers *office partitions *closet doors Is also Available in Stainless Steel finish. Components i 1 Rail 10 feet long and 1\" in diameter . ( longer rail available ...
Come From Calusa Barn Door Hardware
UnitekFiber supplies 4 ports wall mounted optics Faceplate & FTTH Terminal Box. This fiber optic termination box rack mount is a compact and cost-efficient unit, designed specifically for indoor FTTx applications. It is suitable for 4 simplex adapters and 4 duplex LC adapters. ...
Come From ShenZhen UnitekFiber Solution Limited
Complete set of Geneva Brass finish Stainless Steel Barn Door Hardware specially designed for glass doors, 3/8\" and 1/2\" thick, suitable for room dividers, office partitions, and closet doors. Rated for doors up to 100Lbs. Easy installation, No holes needed to be drilled in ...
Come From Calusa Barn Door Hardware
Complete set of Bali Series Stainless Steel Bypass Sliding Bath Enclosure Hardware Set. Components include the following items: 1 Rail up to 73\" long 2 Rail to Wall Holders 8 Wheel assemblies 1 Bottom guide 2 Door stops 2 24\" Single Sided Towel Bars 1 Special wrench Visit us ...
Come From Calusa Barn Door Hardware
·壁挂方式 低故障率、超长寿命 金属纽扣 ·具有盲文功能 ·尺寸:340*94*13mm(高、宽、厚) ...
Come From Jiujiu new energy Co.Ltd
The Cosuper PPL3000 rack mount inverter 48v is ideal for providing backup power to your essential equipment such as telecom, audio and computers. It will produce 3000W of high quality power supply with pure sine wave at a continuous 220V AC output. It is able to seamlessly ...
Wall battery storage batteries are fashionable and compact. This type of wall mount home power storage with solar panel battery wall storage system is easy to install with a simple design. Its design is compact and integrated so that it can be installed indoors or outdoors. ...
Come From Huizhou Liyuan New Energy Co., Ltd
A residential power energy storage stack mount system is a type of residential energy storage solution that consists of multiple battery modules stacked vertically. The design of this kind of stack mount residential energy storage systems allows for increased energy density and ...
Come From Huizhou Liyuan New Energy Co., Ltd