LED Smd Strip

9.Damaged by corrosion will not be protection against corrosive agents such as moisture and condensation and other harmful elements.

8.Pay attention to standard ESD precautions when installing the ribbon

7. When mounting on the metallic or otherwise conductive surfaces, there needs to be an electrical isolation points between ribbon and the mounting surface

6.Please ensure that the power supply is of adapters power to operate the total load

5.Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the ribbon

4.Correct electrical polarity needs to be observed. Wrong polarity may destroy the ribbon

3.Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations.

2. Assembly must not be damaged or destroyed on some conductive bus of the circuit board

1. The SMD light ribbon itself and all their components may not be mechanically stressed

Safety Information:

4.The minimum bending radius is 2cm. The ribbon may be bent over a smaller radius of the circuit board containing no electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue.

3.The mounting of the ribbon is facilitated means of double side adhensive on the back surface of the ribbon. Care must be take to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirty partied. The mounting substrate must have sufficient structural integrity. Take care to completely remove the adhensive backing. Once the ribbon is appropriately positioned. Press on the ribbon with about 20N/m2 (refer to application techniques of 3M adhensive tapes)

2.The smallest unit (50mm or 100mm, 3 LEDs) can be removed by cutting with scissors between the designated solder pads.\

1.Solder connection should only be performed on designated solder pads (marked with

Product description
1) linear separable LED strip on flexible printed circuit board with self-adhen

  • Certification:ISO
  • Country:China (Mainland)
  • telephone:86-755-81531101
Supply Ability: 100k meters
Minimum Order Quantity: USD1000
Payment Terms: L/C,T/T,CASH
Port: Shenzhen or Hongkong
Certification: ISO
*Your name:
*Your Email:
*To:Light Electronic Ltd.
*Subject:
*Message:
Enter between 20 to 3,000 characters. English only.     Characters Remaining: 0 / 3000
*Enter the secure code shown below Mfrbee security Image      Reload Image

We do inquire for you , please wait ...

Super Narrow 4mm Flex LED Strip

4mm ultra-narrow FPC narrow led strip lights with 3M back tape, 120 LEDs/m, 24V low voltage, 500-600lm/m available, CRI 90+, IP20-IP68 protection level available for customization of ultra thin led light strips. Technical Information of W4 Super Narrow 4mm Flex LED Strip Item ...

Come From PANERALUX LIGHTING(NINGBO) CO.,LTD

10mm LED3014 280PCS/m Flex LED Strip

10mm wide 280 LEDs/m strip light with 3M back tape, 24V voltage, CRI 90+, IP20-IP68 protection level available for customization. Technical Information of W10N280 10mm LED3014 280PCS/m Flex LED Strip Item NO. SMD Voltage LEDs/M Power/M CCT Lm/M CRI W10N280 3014 24V 280LEDs/M ...

Come From PANERALUX LIGHTING(NINGBO) CO.,LTD

10mm LED2835 240PCS/m Flex LED Strip

Standard led strip lighting 10mm with 3M back tape, 24V voltage, CRI 90+, IP20-IP68 protection level available for customization for standard led strip lighting. Technical Information of W10N240 10mm LED2835 240PCS/m Flex LED Strip Item NO. SMD Voltage LEDs/M Power/M CCT Lm/M ...

Come From PANERALUX LIGHTING(NINGBO) CO.,LTD