SAWMILL-COMPLETE PRODUCING LINE

FAX. +39 0423-859864

TEL. +39 0423-650125

31031 CAERANO DI SAN MARCO (TV) ITALIA

Via Mazzini, 79

DIEFFEGI S.r.l.

Giacomo Piovesan

BEST REGARDS,

Waiting to hear your views, extend cordial greetings.

At your disposal to establish a negotiation,

The work done by A. Costa technicians is also a further guarantee.

From the photos, you can see that the renewed line is considered almost new.

Carpets, gears, motors, chains were replaced with new ones.

The plant is completely renewed by technicians employees A. Costa who know very well the machinery.

The A. Costa Righi is an Italian leading manufacturer of machines and complete plants for the sawmill industry, woodworking.

Machinery products by A. Costa.

The plant is complete as logs or prisms entering and leaving boards and material chips.

Productivity in 8 hours is given to 40 cubic meters of material cut using 12 persons.

Total 12 persons.

There are 10 persons more 1 people that use crane to load logs and 1 people that use muletto [FORKLIFT TRUCK] to takes away the ready packs of wood elements.

People who work in the line are draw in the lay out.

Cutting speed line : from 4 meters to 20 meters / minute.

ADDITIONAL INFORMATION

Width cutting : 350mm

Maximum thickness cutting : 180mm

MULTILAME

Maximum length of the logs 4 meters

Prisms of any width on ADDITIONAL LOADER (*)

Maximum 280 mm diameters on CARICATRONCHI [LOADING LOGS]

Minimum 120 mm diameters on CARICATRONCHI [LOADING LOGS]

MEASURES OF LOGS

Wood chips will continue in inclined tape rubber to be loaded on some means of transport.

The chips that came out is 4 cm long and 1 cm large.

The chipper has 100 CV and the width of entrance is 60 cm.

The rubber roller n. 17d pass under the position n. 10 and arrive on CHIPPER.

After the Troncatrice, there is a rubber roller (17c) that put pieces of wood elements into the main roller 17d.

After the TRONCATRICE, wood elements continue into roller n. 15c / 15d and arrive on position n. 21 where one person produce wood elements parcels.

Wood elements produced with one spindle multiple ripsaw, continue and go into TRONCATRICE (15a) where one person cut wood elements on the correct desired length.

The other person that work after one spindle multiple ripsaw, take and put slabs into roller n. 17d.

Here, you produce other wood elements and slabs.

At the position n. 10, there is a person that take slabs and wood elements and put into ONE-SPINDLE MULTIPLE RIPSAW.

3) Slabs arrive from TWO-SPINDLE MULTIPLE RIPSAW, with RUBBER ROLLER n. 17d that receive slabs from ROLLER n. 17a.

2) Slabs arrive from TRONCATRICE, with RUBBER ROLLER n. 17d that receive slabs from ROLLER n. 17f / 17b.

1) Slabs arrive from LOG EDGING SAW, with ROLLER n. 9.

On the lay out, at the point n. 10, there is a position where arrive slabs.

The prisms are cut into the desired lengths size, go inside ROLLER (n. 5) [RULLIERA] and then enter on the CENTRATORE (6) of MULTILAME (7) [TWO-SPINDLE MULTIPLE RIPSAW] where the boards will be produced.

The plant was implemented with an ADDITIONALE LOADER (*) that can load prisms of any width from other machinery like SAW LOGS, GATTER, etc.

The prism continues on the DISCHARGE OF MULTIPRISMA (n. 3) to fall into ROLLER (n. 4) [RULLIERA] where then is accompanied inside the TRONCATRICE (n. 22)

The prism continues on the DISCHARGE OF MULTIPRISMA (n. 3) while slabs side splash onto ROLLER (9)-(10) [RULLIERA]

The rollers are entering the logs in LOG EDGING SAW and there the prism is created (n. 2) [PRISMATRICE]

The logs are placed on a ROLLER INTRODUCER SHEATH (n. 1b) [INTRODUTTORE A RULLONI]

The logs are transported automatically by LOADING LOGS (n. 1a) [CARICA TRONCHI]

PRODUCTION PROCESS

I send you some more information about the production process and machinery:

Im here to present you our complete renewed line to cut logs.

We sell a compleate renewed line. You can produce 40 cubic meters per day. You can produce wood elements and chips.