Injection Molding Silicone Rubber
Product Details
Its the non-dangerous goods, and it should be transported as the common chemicals.
Keep in dry place, the shelf time is nine months(Below 25)
7.Storage and Transportation:
Specification:40kg/set(A20 kgB20 kg); 400kg/setA200 kgB200 kg
6.Package:
5.This product should be avoided being mixed with another kind of organic tin catalyst such as amines, sulfur, phosphorus compounds and some metal salts.Otherwise,the catalyst of this product will be useless that the mixed material will not be cured.
4.Its non-dangerous goods.But pls dont have it touch mouth or eyes .If it happens,pls flushing yourself quickiy with enough rinsing.
3.It has the connection for curing time to temperature of the material, the lower for the temperature,the longer for its curing time.
2.The mixed material should be in sealed storage and be used up during the safety operation,or itll slowly cure to wastage
1. Mixing A&B compenent equably before using.
5.Precautions:
Injection molding:Put the mixed material which has been defoamed into the mold.The injection molding should be made under appropriate pressure,temperature , cycle and other conditions.
pumped when there is no bubble. Deaeration time is suggested to be 5 to 10 minutes or so.If there is no deaeration device,the next step can be proceeded when there is no foam in the mixed material,usually one hour after mixing.
Whipping: Adding B to vessel with A then mixing equably.
Defoaming:: Put the mixture in the vacuum deaeration device.Usually,it should not be
Measurement: Be exact Metage for A and B components.
4.Usage:
2.0
2.0
2.0
2.0
2.0
%
Linear Shrinkage
13
12
11
10
8
%
Tensile set
30
30
35
35
15
N/mm
Tear Strength
300
400
550
500
400
%
Elongation At Break
7.0
8.0
8.0
7.5
6
Mpa
Tensile Strength
70
60
50
40
30
ShoreA
Hardness
1.14
1.13
1.10
1.08
1.07
g/cm3
Gravity
700
500
300
70
50
Pa.S
Voiscosity
Semi-transparent
Semi-transparent
Semi-transparent
Semi-transparent
Semi-transparent
Exterior
Item
ADL3106-70
ADL3106-60
ADL3106-50
ADL3106-40
ADL3106-30
Unit
|
Property Model No. 3.Technical parameters:
ADL3106 serious has excellent elasticity and properties of anti-aging and resistence to high temperature afer curing under certain temperature(the temperature can be adjusted according to different demand).It has low linear shrinkage,resistence to impact fatigue,good thermal stability and cold resistence(the operating temperature is 60250).Below 20 ,the safe operating time in a sealed state after component A and B being mixed is 2 days.When the temperature becomes higher,the operating time will be shortened. |
high tensile injection mold RTV2 liquid silicone rubber
- Color:Semi-transparent
- Model Number:ADL3106
- Brand Name:Andalu
- Place of Origin:Guangdong China (Mainland)
- Country:China (Mainland)
- telephone:0086-0755-83953360
| Color: | Semi-transparent |
| Model Number: | ADL3106 |
| Brand Name: | Andalu |
| Place of Origin: | Guangdong China (Mainland) |
You may also like
- injection mold
- plastic injection mold
- plastic injection molding
- injection molding machine
- injection molded
- injection molding plastic
- injection plastic mold
- metal injection molding
- injection molding parts
- injection blow molding
- mold injection
- injection mold plastic
- injection molded plastic
- injection mold maker
Send inquiry / quota request to Injection Molding Silicone Rubber
Relate products of Injection Molding Silicone Rubber
Injection Mold Design Engineering Injection mold engineering is a procedure at the first stage of injection molding process, which develops the injection mold designs to improve the effectiveness and efficiency in injection molding. Plastic mold design technical team of R&D and ...
Come From Taizhou Huangyan Fow Mould CO., LTD
Insulator Silicone Rubber is one of the most widely used materials for insulating electrical equipment due to its excellent electrical insulating properties. YF POWER, a leading manufacturer of electrical equipment, produces high-quality insulator properties silicone rubber ...
Come From Guangdong Yufeng Industries Co.,Ltd
Plastic Mould Industry The industrial plastic injection mold is replacing metal products in many fields of industrial applications to meet the requirement of lightweight industrial equipment and cost-reduction. Green Vitality has accumulated many experiences over the years in ...
Come From Green Vitality Industry Co., Limited
When it comes to custom injection molding, precise moulds and precision equipment are required for precision molding or PIM. Among the topics covered in this blog are general ideas, specific traits and qualities, as well as specific options for plastic materials, precision ...
Animal Silicone Cake Mold This silicone bunny cake mold is a mold made of food-grade silicone material, which can be used to make cakes, pizza, bread, mousse, jelly, prepared food, chocolate, pudding, fruit pie, etc. As a silicone product manufacturer, YF animal silicone cake ...
Come From Shenzhen YF Technology Co.,Ltd
Purple rubber wristbands made by YP Promotion are beautiful and perfect for couples. Custom orders are accepted. Specification of Purple Silicone Wristbands with Custom Logo Material: 100% high-quality silicone material with SGS certificate, Eco-friendly, harmless, non-toxic, ...
Come From Yppromotion
Orange rubber wristbands provided by YP Promotion can be personalized. From the size, color, design that you can give us your specific requirements about the orange silicone wristband. YP Promotion will make a perfect orange silicone bracelet that you really need. Specification ...
Come From Yppromotion
Packson - Medical Plastic Injection Molding Expert Packson sets itself apart from other medical injection molding companies through its distinguished ISO certification for medical injection molding services. Holding certifications for both ISO 13485:2018 and ISO 9001:2008, ...
Come From Packson Mold Co., Ltd
Packson - Expert in 2K｜Multi-shot Multi-component molding is a highly efficient and cost-effective technology that enables the molding of custom plastic parts using two or three plastic resins or colors in a single operation, resulting in faster cycle times and flash-free ...
Come From Packson Mold Co., Ltd
For more than 15 years, Packson Mold has become an excellent manufacturer that is enabled to make parts with high tonnage and large size thanks to our one-stop facility. We are keen to meet your injection molding needs with single and convenient sources. Thanks to our advanced ...
Come From Packson Mold Co., Ltd
