IF Series door

3.01 Installation
Raynor DuraCoil OPTIMA shall be installed by an authorized Raynor Garage Door Distributor.

Part 3 - Execution

2.11 Warranty
The Raynor DuraCoil OPTIMA and its components shall be free from defects in material and workmanship for a period of one year from the date of delivery to the original purchaser.

2.10 Finish
All non-plated components of the door shall receive one coat of rust-inhibitive primer.

2.09 Windload
Doors shall be designed to withstand 20 pounds per square foot (97.64 kg/sq.m.)  windload. Other windloads are available.

2.08 Operation
Manual operation to be provided with inside lift handle and locking bar (padlocks by others). Not recommended for doors over 8' (2438mm) wide or 7'4" (2235mm) high. Chain hoist, crank, or motor operation recommended on all doors requiring heavier than standard gauge. Chain operation shall be by means of reduction gears and galvanized hand chain.

2.07 Hood
Hood shall be 24 gauge prime painted, hot-dipped galvanized steel with rolled edges.

2.06 Counterbalance
The curtain shall be counterbalanced by means of oil-tempered, helical torsion springs, grease-packed and mounted on a single continuous steel torsion shaft. Springs shall be compression spring design to facilitate any counterbalance maintenance.

2.05 Barrel
The barrel shall be made from a minimum 4-1/2" (114.3mm) O.D. x .120" (3.1mm) wall structural steel pipe. Deflection of pipe under full load shall not exceed .03" (.8mm) per foot of span. All 4" (102mm) and 6" (152mm) barrels shall include a galvanized steel removable plug to facilitate counterbalance maintenance.

2.04 Brackets
Mounting bracket plates shall be made from a minimum 3/16" (4.8mm) steel plate and attached to the wall angle of the guide assembly with 1/2" (12.7mm) diameter Class 5 hardened bolts. The drive side bracket shall be fitted with a sealed ball bearing.

2.03 Guides
All guide assemblies shall be fabricated from three structural steel angles. Guide angles shall be minimum 3" x 2" x 3/16" (76.2mm x 50.8mm x 4.8mm) and fitted with two removable curtain stops each. Wall mounted angles shall be continuous type.

2.02 Slats
The curtain shall consist of steel interlocking flat slats not less than 18 gauge, with 3/4" (19.1mm) thick, polyiso foam board core included within the entire length of each slat. Steel slats shall be commercial quality hot-dipped galvanized (G-90) steel per ASTM A-653, and painted with a primer and a finish coat in gray. The back cover shall be a 24 gauge (or 22 gauge), prime-painted, hot-dipped galvanized steel cover. The door shall be provided with a vinyl jamb seal and rubber hood baffle as standard. The curtain U-value shall be 0.16 and R-value shall be 6.24.

2.01 Curtain
Lateral movement of the slats to be contained by means of cast-iron galvanized endlocks fastened to the ends of every other slat with zinc-plated steel rivets. Windlocks shall be provided as required by door size or special windload requirements. Windlocks to be galvanized cast-iron and fastened with zinc-plated steel rivets. Bottom bar shall be two steel angles, minimum 1-1/2" x 1-
1/2" x 1/8" (38.1mm x 38.1mm x 3.2mm). Bottom astragal shall be single-contact type.

Part 2 - Product

1.01 Related Work
Opening preparation, structural metal work, access panels, finish or field painting,
field electrical wiring, wire, conduit, fuses, and disconnect switches are in the
scope of the work of other divisions or trades.

1.01 Furnish and Install
All Rolling Steel Service Door work including electric operators, controls, and
accessories as shown on the drawings and herein specified.

1.01 Work Included
Doors shall be DuraCoil OPTIMA as manufactured by Raynor Garage Doors
 of Dixon, Illinois.

Part 1 - Generalnn

Specifications