Encoder E4 Miniature Optical Kit Encoder

Place housing (cover) on. With thumb and finger, squeeze ears together to insure that cover fully latches.

Slip codewheel onto shaft until it bottoms out against spacer tool. Spacer tool provides an air gap of 0.07" 0.03". Tighten set screw with either the hex wrench / hex driver while pressing down on codewheel.

Place spacer tool on optic module as shown below.

Transfer Adhesive:Peel off paper backing, place centering tool into center hole of base, slip entering tool onto shaft and slide base and centering tool down onto mounting surface as one piece. Press to form a good bond, then slip centering tool off shaft and continue with standard mounting instructions.

Place base onto shaft. Secure base to mounting surface using two screws.

Description: Hex wrench, .050" flat-to-flat for 3-48 or 4-48 set screws.

Description: Hex driver, .050" flat-to-flat for 3-48 or 4-48 set screws.

Description: This reusable tool is used to properly space the codewheel from the encoder base. Nylon. Round. Provides air gap of 0.07" to 0.03".

* See Ordering Information below for available Shaft Diameters.

Please note: A centering tool is highly recommended when using the T-option transfer adhesive.

Material: Aluminum.

Description: This reusable tool provides a simple method for accurately centering the E4 base onto the shaft.

When mounting holes are not available, a pre-applied transfer adhesive (with peel-off backing) is available for "stick-on" mounting. Use the centering tool (above) to position the base. T-option specifies transfer adhesive.

Provides alternate metric M2.5x.45mm, length 6mm screws. When M-option is NOT specified the default is #3-48 x 1/4" screws.

L-option To reduce the average power requirements, the L-option version of the E4P power can be strobed on just long enough to sample outputs A and B. This option is the same as our standard E4P, except the internal power bypass capacitor is not installed. The outputs settling time is typically 200 to 400 nano seconds after power up. The minimum sample frequency must be less than the maximum RPM X the CPR / 10.

The H-option adds a hole in the cover for the shaft to pass through:

For complete details see the page.

A leads B for clockwise shaft rotation, B leads A for counter clockwise shaft rotation viewed from the shaft/bushing side of the encoder (see the page).

* Includes axial play.

    • Minimum shaft length of .285"
    • Fits shaft diameters of .059" to .157" (1.5mm to 4mm)
    • High retention snap-in polarized connector
    • Accepts .020" (.5mm) axial shaft play
    • Off-axis mounting tolerance of .010"
    • Tracks from 0 to 60,000 cycles/sec
    • 100 to 360 cycles per revolution (CPR)
    • 400 to 1440 pulses per revolution (PPR)
    • 2 channel quadrature TTL squarewave outputs
    • -20 to +100 C operating temperature

    The E4 miniature encoder is designed to provide digital quadrature encoder feedback for applications with limited space constraints. The E4 utilizes a traditional...

  • Country:United States
  • telephone:1-3602602468
Minimum shaft length of .285"
Fits shaft diameters of .059" to .157" (1.5mm to 4mm)
*Your name:
*Your Email:
*To:US Digital
*Subject:
*Message:
Enter between 20 to 3,000 characters. English only.     Characters Remaining: 0 / 3000
*Enter the secure code shown below Mfrbee security Image      Reload Image

We do inquire for you , please wait ...

Optical Encoders/ E4

Compact Miniature size best for NEMA 8, 11, 14, and 17.? High retention Snap-in polarized connector? Tracks from 0 to 100,000 cycles/sec? 100 to 300 cycles per revolution (CPR)? 400 to 1200 pulses per revolution (PPR)? -10 to + 85oC operating temperature? Low power strobe ...

Come From iNNOTiCS, inc.

Encoder A2K Absolute Optical Encoder: Kit Version

Installs onto shafts up to 10mm dia. 12-bit resolution, and resolution field programmable from 2 to 4096 codes per revolution (3600 factory default) Full 360 degrees range, and position update rate is 250 times per second Low power drain of 18.5 mA max., and 1.5 mA in sleep ...

Come From US Digital

Encoder E2 Optical Kit Encoder

Quick, simple assembly and disassembly Rugged screw-together housing Accepts .010" axial shaft play Tracks from 0 to 100,000 cycles/sec 32 to 1250 cycles per revolution (CPR) 128 to 5000 pulses per revolution (PPR) 2 channel quadrature TTL squarewave outputs Optional index (3rd ...

Come From US Digital