Tropical Fish Food

Description: Instruction of the Expert's Choice for an External Filter 360L/HPlease read entire the instruction prior to use.Caution:1. Please read and carefully inspect the important warning labels on the prodouct.2. Check first the voltage is appropriate for the filter drum ,the power plug is secure and the socket is not shared with other devices.3. Make sure the product is properly assembled before use.The filter drum must be filled with water before it can be plugged into the power outlet. The motor may otherwise race and become damaged.4. Do not disassemble the product's main motor even if the system is malfunctioning. Please take the product to an authorized service point if it malfunctions. 5. If the power cable is damaged, discontinue use.The product's power cable can't be replaced separately.6. Make sure that the power cable is not mounted too high and that it does not provide a path for water run-off to reach the power socket. This is to ensure that water does not enter the plug or socket.7.The product is only suitable for indoor aquariums.Water temprature 10?J~35?J8.Unplug the product from the power supply when not in use, when installing/removing components,or when cleaning.9. Add full water one day for new aquarium before fresh fish arrive in.Installation Instructions:A: Hang-on B: Table StyleConnect the water outlet and connect piping as shown in the diagram. The whole package included all essential filter materials.A. Hang On (Attached outside the tank ) Ref Drawing:1. Installing Inlet Pipe:Sucker (R) installs to Clip(S1.S2)and Assembly Elbow Head (M). Extend Pipe (Q).Inlet Net (Q3).The pipe length can be freely adjust according to user's demand.(Ref.:Drawing 2a)2. Installing Outlet Pipe.:Sucker (R) installs to Clip (S1).Then according to user's demand to assemble Rain Pipe(P),Stopper(P4).And fix them to the Emblow (Size.:Short)which should be connected with Inlet & Outlet Head.The Outlet and Rain Pipe can be chageble to show different spray on water surface.(* Rain Pipe(P) &Outlet Port(P3)for both Exchange using.)3. Installing Inlet & Outlet Port.:Connecting Plastic Cap(L). Elbow Head (M).Long size Elbow Pipe (T) to fix Pump Stand of Outlet & Inlet Port.Then fixxing Elbow Pipe to Elbow Head and Inlet&Outlet Port by anti-lockwise.4. Installing completion.:Take Out Hanger(U1)B. Placed on table.: In order to beutify the Surroundings of aquariums,the length of Soft Pipe can be adjusted according to aquariums size (Ref.: Drawing 4).The water tolerance between the filter & aquarium is within 60cm.1. Inlet & Outlet Pipe Installing.:(Ref.: Drawing 2. 2a~2c: Operative).2. Installing Inlet & Outlet Port.:Connecting Plastic Cap(L). Elbow Head (M). Long size Elbow Pipe (T) to Fixed Pump Stand of Outlet & Inlet Port.Then fixxing Elbow Head and Inlet&Outlet Port by anti-lockwise.C.Usage: 1. Turn on Knob (Adding Water)then filled with water fully and Locked.2. Socket the power plug to run normally. Maintenance.: 1. Choosing the dish-cloth for filter's surface cleaning.Keep away from the Gasoline of Cleanser in order not to rot the body-cover.2. Stop running at once when it appears unusal voice or high temperature. 3. Regular washing or replace filter material,Include Sponge (B1).Cartridge(B2) & Bio Ring (W),in order keeping the filter in best condition.4. Washing or Replace Filter Material.:4.1 Disassembled Motor- Head:Turn Off "Power ",then take out Soft Pipe Inlet & Outlet. (To prevent water Outlet-Siphon from Tank, the soft Pipe needs to pun on tank upper.)Pull up Side Hook (F2),then pull up Hook Sets (F1) as shown in(Ref.:Drawing 7).Pull on both side Hook and Hook Sets,then take out Motor Head.Ref Drawing: 6-(1) &(2)4.2 Disassembled Filter Cup: First take out Cup-Cover(C)&Filter Suction Cup (B), then fasten the hook which connected the Cup-Cover(C)&Filter Suction Cup (B) shown as in(Ref.:Drawing 8).4.3 Replace & Washing.: Take out Sponge (B1). Cartridge (B2)& Bio Ring(W) from Filter Cupto replace or washing. 4.4 Installing.:Installing Filter Tank & Motor Head by anti-lockwise. Then turn on knob(K), lock Adding Water(K) after filled with water,to run again by inserting electrical source.(Ref.:Drawing 8 & 5 )