Sell cnc router kits wantai spindle stepper motor @China (Mainland)
CNC Router kits 3Axis CNC 1600OZ-IN & 3256OZ Wantai Spindle Stepper Motor Grind Mill |
|
Product No.: N2012611173158 |
|
|
This item includes: 2 PCS Nema 34 Stepper Motor with Single shaft 1600oz-in holding torque, 1 PC Nema 42 Stepper Motor with Single shaft 3256oz-in Holding torque, 2 PCS Stepper Driver DQ860MA with 7.8A replacing MD882, 1 PC Stepper Driver DQ2272 With 8.0A Peak current,7.0A rated current, 110-220VAC, 200 Microstep, 2 PCS Power Supply for 350W,60VDC,5.9A, 1 PC Breakout Board, 1 PC DB25 Cable
Note: Alternating current on driver to connect the power,there is no need for any power supply to convert.
1, Stepper Motor 1, Technical Specifications Part No.: 85BYGH450C-012 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 5.7V Current: 3.5A/phase Resistance: 1.9 Ohm/phase Inductance: 22 mH/phase Holding torque: 11.3N.m 1600oz-in Rotor inertia: 3600g-cm2 Number of wire leads:4 Weight: 5 kg Length: 151mm
Note: Nema 34 Stepper Motor with 1600oz-in holding torque on single shaft, front shaft length is 37mm with 25mm flats length, flats length, the diameter for motor shaft is 14mm.
RED A+ GREEN A- YELLOW B+ BLUE B-
2, Stepper Motor Driver Introduction The DQ860MA is an economical microstepping driver based on patented technology of Wantai Motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors. By using the advanced bipolar constant-current shopping technique ,it can output more speed and torque from the same motor,compared with traditional drivers ,such as L/R drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple,therefore less motor heating is achieved.
3,1PC Nema 42 Stepper Motor of 4200OZ-In Holding Torque, Technical Specifications Part No.: 110BYGH150-001 Frame Size: NEMA42 Step Angle: 1.8 degree Voltage: 5.44VDC Current: 6.8A/phase Resistance: 0.8Ohm/phase Inductance: 15mH/phase Holding torque: 230 Kg-cm 3256oz-in Rotor inertia: 1090g-cm2 Number of wire leads: 4 Weight: 8.4kg Length: 150mm Shaft Diameter: 19mm with keyway
Please tell us if you need Double shaft or single shaft, we can manufacture both for you. If you need Double shaft, please tell us your requirements for length of front and rear shaft, as well as the diameter. So that we can offer you the quite good products, thanks!
4, Stepper Motor Driver DQ2722M, 110-220VAC, 7.0A, 200Microstep
The DQ2722M is full digital 2 phase stepper driver based on DSP control. The drive voltage of which is from 110V to 220VAC. It is designed for use with the 2 phase hybrid stepper motor of all kinds with 86mm to 130mm outside diameter,regulated phase current 1.2A to 7.0A. The circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly without noise and vibration. The highest micro step is 60000ppr. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, computer embroider machine, packing machine and etc.
FEATURES
l High performance, low price l 16 channels constant angle, constant torque micro steps, highest micro step: 40000ppr l Highest response frequency: 200Kpps l Current of winding will be reduced by approximately 50% when no step pulse command is received for 0.1 second l Opto-isolated signal I/O l Drive current is adjustable in 16 channels from 1.2A/phase to 7.0A/phase l Single power supply from 110V to 220VAC l Phase terminal memory function (motor phase terminal is memorized after input pulse train stopping 5s and it is recovered when stepper driver power on or signal MF changes from low level to high level) Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Communication, Household Appliance, Water Pump, Milling Machine, Engraver Machine, CNC Routers.. etc automatic equipment of various trades.
We Ship Worldwide!
We product all kinds of motors & driver. And we can manufacture products according to our
customer's design.
Currently we are looking for qualified stocking distributors with competitive price and good
discount in WORLDWIDE for mutually beneficial long-term relationship. We try our best to
support our distributors and business partners to develop more market percentage.
Please join us, let¡¯s create the glorious future together!
|
Post by wantai motor Electrical Equipment & Supplies @2013-01-16 07:19:29
Contact with wantai motor
Social Connect
Contact Us
- ShaoYaoJu , ChaoYang district , Beijing , China